Utilize this basic maintenance method to keep your hot water heater working effectively and dependably.
Water heaters work hard to offer you with warm showers, clean garments, and dazzling pots and pans.
Demonstrate your water heater some love by following a planned maintenance program that will keep it working for its approximated 15-year life-span, and potentially beyond.
Here is what you must do:
Set the thermostat to 120 degrees Fahrenheit. You’ll conserve up to 5% on energy costs for each 10 degrees you lower the temperature level, and you’ll also minimize the risk of scalding.
Unless otherwise defined in the manual, keep a 2-foot clearance around the unit.
- Empty about a quarter of the tank a couple of times a year to get rid of sediment and debris.
- Shut off the cold water supply, connect a garden tubing to the drain valve, and run the water into a pail till it is clear.
If the water stays hazy, open the water supply valve briefly to stir up any leftover particles before draining the tank once again. This also reduces the unit’s sound level.
Check the temperature-pressure relief valve once a year by rapidly discharging it 2 or 3 times. Keep a lookout for tiny leaks from the valve after the testing.
Examine the sacrificial anode rod every 3 years by removing the hex and loosening up head screw.
Change the rod if any of the following conditions exist:
(A 13-inch zinc-aluminum anode rod expenses roughly $16).
- More than 6 inches of core steel wire is visible.
- The rod is just around 1/2 inch thick.
- Calcium has actually been applied to the rod.
- Insulate older units with a fiberglass coat to boost effectiveness, making sure not to come into contact with the flue (newer units are currently insulated; consult your owner’s manual to confirm).
Insulate the cold and hot water lines.
When you leave for an extended period of time, set the thermostat on gas heating units to “vacation,” which keeps the pilot burner lit but does not warm the water.
Some jobs are better left to the pros...
Consult a Pro. Get No-Commitment Estimates For Your Project.
How Often Do You Need Hot Water Heater Upkeep?
Water Heater care is required not just for keeping you warm throughout the winter months. Warm Water Heating systems that are damaged or malfunctioning can additionally lead to serious burns to you and your family.
Let’s go over how regularly you must perform water heating unit maintenance.
In general, the life-span of your water heater will be between 8 and twelve years. Naturally, a variety of aspects can have an impact on this life-span.
- The placement of the water heater in your house.
- How properly it was set up.
- The make/model of the heating unit itself.
- And even the quality of care you give will all have an impact.
Specialists advise getting your hot water heater emptied out at least once a year for repairs and maintenance. Essentially, this means that your tank must be drained with a hose and then refilled with clean water.
This helps in the removal of excess dirt from your heater, which, if left unchecked, can cause major damage and blockages in your system. An examination and deep cleaning of the hot water heater’s coils, rods, and other parts must be included in the maintenance.
It’s time to start paying closer attention to the signs that something isn’t quite right with your heating unit. You must act as soon as possible if you find any of the following signs. A defective water heating unit might blow up, causing serious harm to you or your family.
1. You See Leaks
Naturally, you’ll realize you require water heater maintenance if you see a leakage or a big puddle around your heating unit. Not all indications of a leakage are as clear.
In general, you must look for leaks around your warm water heating unit at least as soon as a month. Try to find drips, damp flooring, or perhaps a moldy odor around the heating unit.
2. Water Pressure Is Low
Low water pressure is annoying, but it is also an indication that your hot water heater needs to be serviced. This is probably due to the accumulation of minerals or other kinds of dirt.
The pressure might also be low due to a kink in the pipeline or improper setup.
Your water heater will make a couple of random noises that are not alarming. What if you begin to hear a lot of clanging, clicking, or even something that sounds like popping?
It is probably an indication of a more serious issue. Typically, what is occurring is that your heating unit is overheating as it tries to change for blockages in the system.
Not just will this increase your warm water expense, but it might also raise your risk of burns if you go into touch with the heating unit.
4. Rusty Water
Another warning indicator is that something is wrong with your hot water heater. Examine the water flowing from your faucets.
- Is the color reddish-brown and rusty?
- Is there an extremely metallic taste to it if you’ve tried to drink it?
- Does your water often appear dirty?
This is because the pipes themselves have probably begun to rust. Sometimes, you might have the ability to address this issue without the assistance of an expert.
Begin by draining as much warm water as possible from your heating unit. (For your well-being, we advise utilizing a five-gallon pail.) If, after the 3rd five-gallon pail, you’re still seeing the reddish-brown color?
It means that the issue is with your hot water heater instead of your pipes.
If this is the case, it is best to seek the assistance of a pro. They’ll have the ability to empty your tank more completely, and they’ll probably examine the overall condition of your pipes.
When it comes to water heater maintenance, constantly depend on the services of an expert when in doubt.