1331 Lincoln Hwy,

Levittown, PA. 19056

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

1331 Lincoln Hwy,

Levittown, PA. 19056

7 Proven Ways How To Stop Leaky Sink Faucets

How to figure out the reason for a leaky faucet.

There is absolutely nothing more annoying than a leaking faucet. Not only can it keep you awake at night, however it may likewise cost you more on your water expense. That is why repairing a leaky faucet as soon as possible is always an excellent idea.

 

It’s an easy DIY task with a few tools and the right information.

 

Bear in mind that the repair work method will differ based upon the kind of spout and sink you have, however you can utilize these basic tips to stop a leaky faucet:

 

  • It is very important to watch out for dripping faucets, as a single leaky fixture can waste approximately 20 gallons of water every day! Check your sink to try to locate the reason for the leakage.
  • You’ll need to change the O-ring or tighten up the packing nut if water is gathering around the faucet’s stem..
  • If the leakage is originating from the spout, the faucet handle is probably damaged. Now, it is very important to understand what kind of faucet you have in your property.
  • Cartridge Faucets are most common in current properties, and the cartridge needs to be replaced regularly.
  • A Compression Faucet, on the other hand, is more common in older properties. Due to the fact that the rubber seals can wear out in time, replacing them can generally fix a leaky faucet.

Some jobs are better left to the pros

Consult a Pro. Get No-Commitment Estimates For Your Project.

What you’ll need

A number of the items you’ll need to stop a leaky faucet are already in your toolbox. A Skilled Local plumber advises getting the following products before starting work:

 

  • Rags– for simple clean-up.
  • White vinegar– for cleaning up along the way and losing grim accumulation in the spout.
  • A Philips and flat-head screwdriver– to take out the screw.
  • Replacement parts– to swap out the failed components.

 

You must likewise have an allen wrench or an adjustable wrench on hand to loosen valves and nuts. Slip-joint pliers can do the very same job and provide a better grip on small-sized faucet parts that need to be tightened during reassembly.

Fixing

Follow these steps to stop a leaky faucet, whether it’s a continuous leaky shower faucet or a leaking sink spout:

1. Turn off the water

Prior to doing any repair work, always switch off the supply of water. Look under the sink for the shutoff valves. Close them firmly by turning them clockwise.

 

Overtightening can cause damage, so avoid using too much force. If the valves aren’t under the sink, you’ll need to close the main water valves.

 

These devices are usually found in the basement or near the washing appliance, dryer, or hot water heating unit.

 

After you‘ve closed the valves, switch on the faucet to decrease the pressure and empty any standing water in the pipelines.

2. Close the drain

You’ll be working with small-sized screws when you take out the faucet, and you do not want them to get lost down the drain pipelines. Prevent a disaster by covering holes with plugs or coverings. A rag can likewise be placed down the pipe.

3. Take the system apart

Depending upon your sink, you may need to take out the faucet system to reach the problem, however preferably, you will only need to take out the handle.

 

For ceramic disc faucets, start by removing the set screw and retaining nut before reinstalling the cylinder. The steps are similar for a cartridge faucet, however you will need to take out the retaining clip or nut to change the cartridge. As you take out the parts, keep the order and positioning in mind.

 

This attention to detail makes reassembly a lot easier. Reserve the pieces in the order you dismantled them to help you remember, or snap photos as you work.

4. Examine all the parts

When a faucet begins to leakage, seals, rubber washers, and O-rings are frequently to blame. Examine them for noticeable indications of wear and tear, such as a flattened washer or grooves worn into the pieces.

 

If they appear used, change them. Bring the old components with you to the store to guarantee you get the right replacements.

 

Change the faucet with a washer-less one to help avoid the problem in the future.

5. Clean as you go

Use this time to clean the pieces before reassembling them. Once the parts have been taken out, wash all seals and inside cylinders.

 

Examine the valve seat for mineral deposits that might cause the washer to end up being clogged up and cause leaks. Clean the surface areas with a rag and release the deposits by soaking them in white vinegar.

6. Reassemble the faucet

When the pictures you shot earlier come in useful, this is. Reverse the disassembly process with your tools in hand to assemble the faucet. Never ever force parts to work or press down on the faucet.

7. Test the water flow

After you‘ve completed the repair work, you’ll need to turn the water back on. Professional advice: Make certain the faucet is turned on, and after that gradually turn the water back on.

 

If the faucet is turned off or too much pressure is applied prematurely, it may cause more considerable damage, such as cracking the ceramic disc. Allow the water to flow generally for a few minutes.

Consider replacing rather than repairing

It’s generally a good idea to change it entirely with a new cartridge model if an old faucet is presenting you problems.

If you can’t identify what’s causing the leakage or if a quick solution doesn’t work, it’s much better to hire a plumber who has the skills to effectively identify and fix the problem.

Some jobs are better left to the pros

Consult a Pro. Get No-Commitment Estimates For Your Project.

Proud to Install, Repair, and Service the Following Brands: